Gorilla Playsets Riverview Assembly Manual Download Page 46

Page: 46 / 94

Step 14: Rock Wall

1: Find ten rocks and thirty 1-1/4” pan head screws and washers.
2: Mount the rocks in a staggered manner on the rock wall boards. Three pan head

screws with washers will secure each rock to the wall.
Note: the image shown below is a generic arrangement of rocks on the rock wall. Your

actual configuration may be different that what you see below. Rocks can be arranged in

any pattern as long as they will allow proper access to the fort. Be creative!
3: Place the 5/4 x 2-5/8 x 23-7/8” rock wall top cap on top of the rock wall sides. Fasten

the rock wall top cap to the rock wall sides with 2” wood screws.

Climbing Rocks

Washer

1-1/4” Pan Head

Screw

5/4 x 2-5/8 x 23-7/8”

Rock Wall Top Cap

2” Wood Screw

Page 46

Summary of Contents for Riverview






























































































Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands

Gorilla Playsets Riverview, Assembly Manual

Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands