Gorilla Playsets Riverview Assembly Manual Download Page 57

Page: 57 / 94

Step 25: Mount Swing Beam To Fort

An extra person is needed for this step.
1: Have one person walk the swing beam out to the end of the fort from inside the fort

while the other person carries it by the legs.
2: Line up the pilot holes at the end of the swing beam with the middle holes on the

swing beam plate.
3: Fasten the swing beam to the swing beam plate and swing beam support using a 9”

carriage bolt with a torque washer on top, and a 3/8” lock nut and washer on the bottom.

Place bolt caps over exposed threads after securing.
4: Fasten the swing beam to the swing beam plate from underneath with a 3/8 x 3- 1/2”

lag screw and 3/8” washer.

Torque Washer

3/8” Washer

Bolt Cap

3/8 x 3-1/2” Lag

Screw

9”Carriage Bolt

3/8” Nut

Page 57

Summary of Contents for Riverview






























































































Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands

Gorilla Playsets Riverview, Assembly Manual

Search results

Summary of Contents for Riverview

Reviews:

Related manuals for Riverview

Brands by name

Popular brands