manualshive.com logo in svg

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Manual, Page: 95 / 171

Share
Download
Gorilla Playsets Malibu Pioneer Peak 1500DWR Manual Download Page 95

(4" WIDE)

ROOF STARTER FRONT

(3-1/4" WIDE)

1 X 4 X 76-7/8"

OVERLAP

ROOF STARTER REAR

1 X 4 X 76-7/8"

FLAT TOP END

FLUSH 

STEP 34:  ROOF FRONT SECTION

1: PLACE THE 1 X 4 X 76-7/8" ROOF STARTER FRONT BOARD AT THE PEAK OF THE ROOF OVERLAPING THE ROOF 

STARTER REAR. THE HOLES IN THE ROOF STARTER FRONT SHOULD BE CENTERED ON THE ROOF SUPPORTS, AND THE 

FLAT TOP END OF THE ROOF STARTER FRONT SHOULD BE PLACED FLUSH TO THE TOP EDGE OF THE ROOF STARTER 

REAR.

2: FASTEN THE ROOF STARTER FRONT TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

3:  PLACE THE 1 X 5 X 76-7/8" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE END INTO THE 

GROOVE END OF THE ROOF STARTER REAR.  THIS SIDE OF THE ROOF GETS SEVEN ROOF BOARDS.

4:  FASTEN THE ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

(SEVENTH ONE)

ROOF STARTER FRONT

1 X 4 X 76-7/8"

(FIRST ONE)

ROOF BOARD

ROOF BOARD

1-1/2" WOOD SCREW

87

Summary of Contents for Malibu Pioneer Peak 1500DWR












































































































































































Reviews:

No comments