manualshive.com logo in svg

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Manual, Page: 94 / 171

Share
Download
Gorilla Playsets Malibu Pioneer Peak 1500DWR Manual Download Page 94

WASHER

5/16" X 3-1/2"

LAG SCREW

ROOF BOARD

ROOF FINISHER

ROOF STARTER REAR

(FIRST ONE)

1 X 4 X 76-7/8"

1-1/2" WOOD SCREW

ROOF BOARD

(SEVENTH ONE)

5/16" 

CHIMNEY

2 X 4 X 69-3/4"

ROOF FINISHER SUPPORT

STEP 3

3

:  ROOF REAR SECTION AND CHIMNEY

1:  PLACE THE 1 X 5 X 76-7/8" ROOF BOARDS ON TOP OF THE ROOF SUPPORTS, FITTING THE TONGUE END INTO THE 

GROOVE END OF THE ROOF STARTER REAR.  THIS SIDE OF THE ROOF GETS SEVEN ROOF BOARDS.

2:  FASTEN THE ROOF BOARDS TO THE ROOF SUPPORTS WITH 1-1/2" WOOD SCREWS.

3:  PLACE THE 1 X 4 X 76-7/8" ROOF FINISHER AT THE END OF THE ROOF ASSEMBLY, AND FASTEN WITH 1-1/2" 

WOOD SCREWS.

4: MOUNT THE 2 X 4 X 69-3/4" ROOF FINISHER SUPPORT UNDERNEATH THE ROOF UP AGAINST THE ROOF FINISHER 

REAR

AND ATTACH TO THE REAR CORNER POST USING 5/16" LAG SCREWS AND 5/16" WASHERS.

TIP: USE THE INSTRUCTIONS PROVIDED IN THE APPENDIX TO BUILD THE CHIMNEY. INSTALL THREE ROOF BOARDS 

AND INSTALL THE CHIMNEY ACCORDING TO THE CHIMNEY INSTRUCTIONS.

86

Summary of Contents for Malibu Pioneer Peak 1500DWR












































































































































































Reviews:

No comments