manualshive.com logo in svg

Gorilla Playsets Malibu Pioneer Peak 1500DWR, Manual, Page: 152 / 171

Share
Download
Gorilla Playsets Malibu Pioneer Peak 1500DWR Manual Download Page 152

STEP 27: ROOF BOARDS AND ROOF FINISHERS

1: LOCATE TEN 1 X 5 X 36-3/4" ROOF BOARDS.  SLIDE THE TONGUE OF THE ROOF BOARD INTO 

THE GROOVE OF THE ROOF STARTER.  SECURE THE ROOF BOARD TO THE ROOF SUPPORTS WITH 

FOUR #8 X 1-1/2" WOOD SCREWS.

2: SLIDE THE NEXT ROOF BOARD TONGUE INTO THE GROOVE OF THE PREVIOUS ROOF BOARD.  

SECURE THE ROOF BOARD TO THE ROOF SUPPORTS WITH FOUR #8 X 1-1/2" WOOD SCREWS.

3: REPEAT SUBSTEP 2 FOR THE NEXT 3 ROOF BOARDS.

4: LOCATE A 1 X 4 X 36-3/4" ROOF FINISHER (TONGUE ONLY).  INSERT THE TONGUE OF THE 

ROOF FINISHER INTO THE GROOVE OF THE LAST ROOF BOARD.  SECURE THE ROOF FINISHER TO 

THE ROOF SUPPORTS WITH FOUR #8 X 1-1/2" WOOD SCREWS.

5: REPEAT SUBSTEPS 1 THROUGH 4 FOR THE ROOF BOARDS AND ROOF FINISHER ON THE OTHER 

SIDE OF THE ROOF.

(1 PER SIDE)

ROOF FINISHER

(5 PER SIDE)

WOOD SCREW

#8 X 1-1/2" 

1 X 5 X 36-3/4"

ROOF BOARD

1 X 4 X 36-3/4"

#8 X 1-1/2" 

WOOD SCREW

144

Summary of Contents for Malibu Pioneer Peak 1500DWR












































































































































































Reviews:

No comments