manualshive.com logo in svg

GMT GMT 050, User Manual, Page: 4 / 42

Share
Download
GMT GMT 050 User Manual Download Page 4

 

GMT 050 

 

User manual 

 

 

4 

 

2.

 

Safety guidelines 

These safety regulations cannot eliminate all hazardous situations 

and accidents related to use of the felling grapple. However, they 

will  be  as  effective  as  possible  in  preventing  potential  hazardous 

situations and accidents. 

 

Legal regulations must also be observed in addition to the details and instructions provided here. 

 

Wear appropriate clothing to prevent being trapped by the machinery. 

 

Use PPE such as safety gloves, safety glasses, a safety helmet and hearing protection. 

 

Be aware of the risk of losing your footing when working on/with the felling grapple. 

 

Beware of telephone and electricity cables when working near telephone and high-voltage pylons. 

Keep a safe distance and do not endanger any persons. If you are not confident about the situation, 

contact the local electricity operator. If you are forced to abandon the equipment, your own safety is 

imperative. Do not pause to secure the machinery. 

 

Leave the scene of potential electrical danger as quickly as possible. Never run, but move forward by 

pressing your legs together and walking away. 

 

Make sure that no persons, animals and/or goods are within the 50-meter safety zone (165 feet) while 

the machine is in use.  

Various weather conditions can affect use of the felling grapple. Such conditions include wind, snow 

and/or  storms.  Weather  conditions  must  be  taken  into  account  before  use  of  the  felling  grapple. 

Weather circumstances at the site allow use of the felling grapple must also be determined. If this 

proves to not be the case, appropriate precautions must be taken 

 

Familiarize yourself with the felling grapple before use. Knowledge about (energy) wood felling and 

tree maintenance is also preferred. 

 

Observe all instructions contained in the user manual of the felling grapple, the crane and the carrying 

vehicle in order to prevent hazardous situations and avoid endangering any persons. 

 

The felling grapple may only be used once all safety regulations have been thoroughly read and all 

components have been correctly attached/installed. 

 

The carrying vehicle must be turned off during mounting of the felling grapple. Make sure that the 

system is depressurized, or depressurize it by moving the joystick or handle. This is essential to ensure 

that work is carried out safely. 

 

The carrying vehicle with the felling grapple may in no way whatsoever be operated or repaired if the 

operator is under the influence of alcohol and/or narcotics. 

 

An ability to work precisely is required in order to measure pressures and to set/adjust the felling 

grapple. 

 

A rise in pressure inside/on the system can result in damage to the felling grapple and can increase the 

risk of accidents! 

 

Summary of Contents for GMT 050











































Reviews:

No comments