GMT GMT 050 User Manual Download Page 34 | Manualshive

Page: 34 / 42

GMT GMT 050 User Manual Download Page 34

GMT 050

User manual

34

Note that the pressure on the saw bar is related with the restrictor on the saw bar cylinder. This

restrictor is to adjust the speed when the saw chain hits the wood at saw starting point. If this speed

is too high, the saw bar starts ‘jumping’/stuttering on the wood. After valve 3 has been set the ideal

speed of the saw bar on hard or soft wood can be adjusted with this restrictor.

Valve 8

(factory pre-set,

do not adjust!)

This is the pressure safety valve for the tilt cylinder. If the load is too heavy and the grapple drops too
slowly, this valve protects the tilt cylinder by allowing the grapple to tilt down immediately. If this valve
is set too high, the felling grapple may strike the crane boom.

Valve 11

(factory pre-set,

do not adjust!)

This is the pressure safety valve for the grapple close function. If set too high, it will no longer protect
the grapple cylinder from overload. If set too low, the grapple cylinder will not have enough grapple
strength. The default value is 185 bar and cannot be changed by adjustments to the manifold.

«
...
32
33
34
35
36
...
»

Summary of Contents for GMT 050











































Reviews:

No comments