GMT GMT 050 User Manual Download Page 37 | Manualshive

Page: 37 / 42

GMT GMT 050 User Manual Download Page 37

GMT 050

User manual

37

7.1.3

Saw blade speed

The speed at which the saw blade extends can be regulated by adjusting the regulator valve on the
saw cylinder. As this regulator valve is opened, the speed at which the saw blade extends is increased.
Before the regulator valve can be adjusted, the hex locknut must first be loosened

regulator valve for the saw blade

7.1.4 Braking force of the TTC

(factory pre-set,

do not adjust!)

The braking force is set from factory. The brake pressure, size of brake-cylinders and the accumulator
are designed and set in such a way that the tilt-cylinder is protected against overloading. Never
increased the hydraulic pressure on the brake system it can result in high torsional forces on the
crane end beam.

When the brake is holding the load but the tilt-cylinder is still tilting down then the load that has
been cut is too heavy. Cutting smaller tree parts or branches is the solution to be able to use 100%
braking functionality and the grapple not tilting down. Only then branches can be removed holding
the wood in a steady fixed position.

«
...
35
36
37
38
39
...
»

Summary of Contents for GMT 050











































Reviews:

No comments