GMT GMT 050 User Manual Download Page 36 | Manualshive

Page: 36 / 42

GMT GMT 050 User Manual Download Page 36

GMT 050

User manual

36

Pressurizing the accumulator in case of low pressure

Two persons are required in order to increase the pressure!

Method:
Before pressurizing the accumulator, the regulator valve on the accumulator testing/pressurizing kit
(see below photograph) must be fully closed!

Attach the hose on the regulator valve side to test point J. Attach the hose on the manometer side to
the accumulator test point. Use a (pipe) wrench to tighten the swivel on the test hose!

Once attached, the grapple open function can be operated. As soon as the grapple reaches tilt up
position, the 2

nd

person must slowly open the regulator valve for at least 30 seconds. The accumulator

will now be pressurized.

Excess pressure

Leave  the  regulator valve on  the  accumulator  filling kit  closed.  When  the  grapple  is  in  the  default
position,  grapple  open  and  tilt  down  read  the  manometer  value.  The  final  value  should  be  in  this
position  580  psi  [40  bar]  .  If  the  pressure  is above the  580  psi [40 bar],  it  can  simply  be  lowered.
Carefully open the regulator valve next to the manometer and wait until the pressure drops to the
correct level. Close the regulator valve and detach the pressurizing kit.

Accumulator measuring/filling set

«
...
34
35
36
37
38
...
»

Summary of Contents for GMT 050











































Reviews:

No comments