GILES FSH-2 Operation & Service Manual Download Page 55

Page: 55 / 66

Troubleshooting

This section describes troubleshooting procedures for the

FSH-2, FSH-2A-99 Ventless Hoods

. Refer to the wiring

diagram provided with the unit as needed for more detailed analysis.

6-01.

Troubleshooting Procedures

•

Electrical troubleshooting procedures should be performed

ONLY

by qualified service personnel. Death or

serious injury will result from contact with energized electrical components.

Model: FSH-2, FSH-2A-99

Troubleshooting

Problem

Probable Cause

Corrective Action

Hood will not turn ON

a. Filter Access Cover not properly

postioned & latched.

Confirm cover properly positioned.

START

portion of power switch

not held until hood starts

Press & momenterily hold

START

portion of switch until blower starts.

c. Power switch is faulty

Replace switch.

c. Improper supply voltage

Connect to proper electrical supply.

e. Not properly connected to power

source.

Confirm connections & correct.

f. Blown fuse or tripped circuit

breaker.

Check fuse in hood or breaker at

main electrical panel.

[FILTER MISSING] light ON at start-

a. Baffle or charcoal filter not

installed or not properly seated

Install filter and/or check filter

positioning inside hood.

EAC [WASH] light ON & intermittent

(beeping) alarm sounding

a. Excessive film build-up on fins

Clean the EAC cell,

Section 4.04.2

b. EAC cell is not installed

Install EAC cell

c. Poor connection at contact plate

inside hood.

Check cell position, clean contacts.

d. Faulty EAC contact plate

Have plate inspected, replace if

needed.

e. Missing ionizer wires

Replace wires, (9) required.

EAC [CHECK] light ON; no alarm

sounding

a. EAC shorted to ground (damaged) Replace or repair the EAC cell.

b. High voltage wires shorted to

ground.

Correct shorted condition.

c. Collector fins shorted out due to

excessive moisture.

Eliminiate condensation causes - cold

air being drawn into hood, etc.

Summary of Contents for FSH-2



































































Search results

Summary of Contents for FSH-2

Reviews:

GILES FSH-2, Operation & Service Manual, Page: 55 / 66

Search results

Summary of Contents for FSH-2

Reviews: