GILES FSH-2 Operation & Service Manual Download

Page: 19 / 66

Installation

Model: FSH-2, FSH-2A-99

Model FSH-2:

1. Install appropriate circuit breakers in main electrical panel supplying power for the hood. See

Section 2.03

for required circuit breakers. Breaker size given is for the hood only. Appliance requires separate power

supply, see

Figure 2.03.1 (A)

2. Remove cover on service entrance box and run appropriate size conduit and wire from box to the electrical

panel supplying hood power. Allow sufficient length of wire and conduit to provide slack needed to properly

access unit for cleaning and service.

3. Make all appropriate connections.
4. Reinstall box cover.

Model FSH-2A-99:

1. Install appropriate circuit breakers in main electrical panel supplying hood power. See

Section 2.03

. for

required circuit breakers.

Breaker size given is for the hood only

2. Some

FSH-2A-99

models provide an interlocked power receptacle for the appliance located in the left-side

hood leg or on the rear panel, see

Figure 2.03.1 (B)

When installing a hood with the interlocked receptacle,

the breaker size shall be determined by the electrical load of the appliance being placed under the Hood

(max. load is 50A).

2. Remove the upper rear panel to access terminal blocks. Remove one of the large hole plugs and install an

appropriate conduit connector. Route appropriately sized flexible conduit and wire from the electrical panel

supplying hood power. Allow sufficient length of wire and conduit to provide slack needed to access unit for

cleaning and service.

3. Make all appropriate connections as shown in

Figure 2.03.1 (B)

4. Reinstall rear panel.

2.03.2 Hood Power Connection

IMPORTANT!

Electrical installation materials (breakers, conduit

fittings, wire, etc.) and labor shall be provided by the

customer. Work should be performed by a qualified professional electrical contactor.
Installation must comply with all local code requirements. Giles assumes no responsibility with respect to code

compliance regarding installation and use of this equipment.

Summary of Contents for FSH-2



































































Search results

Summary of Contents for FSH-2

Reviews:

Related manuals for FSH-2

Brands by name

Popular brands

GILES FSH-2, Operation & Service Manual

Search results

Summary of Contents for FSH-2

Reviews:

Related manuals for FSH-2

Brands by name

Popular brands