GILES FSH-2 Operation & Service Manual Download

Page: 39 / 66

Operation

Model: FSH-2, FSH-2A-99

4.02.3

Baffle Filter Installation

BAF

FLE

FILT

BAFF

LE F

ILTE

BAFF

LE F

ILTE

BAFF

LE FI

LTER

Switch arm

must be

actuated by

the Baffle

Filter when

installed, as

shown

①

Insert back edge of filter into hood

(to the back wall)

②

Lift front edge up behind

Front Header Panel

③

Pull filter forward until front edge rests on

support ledge

inside

front panel

④

Allow back edge to drop down and rest on

studs in the rear channel

IMPORTANT!

As shown above, the filter body must engage and actuate the curved actuator lever located at the rear of

hood, on the right side. Filter must be installed so that the slats/slots are vertical, NOT horizontal.

The Baffle Filter has sharp exposed edges, which may cause cuts. Use due caution when handling and

cleaning. Heavy duty rubber gloves are advised.

Summary of Contents for FSH-2



































































Search results

Summary of Contents for FSH-2

Reviews:

Related manuals for FSH-2

Brands by name

Popular brands

GILES FSH-2, Operation & Service Manual

Search results

Summary of Contents for FSH-2

Reviews:

Related manuals for FSH-2

Brands by name

Popular brands