Gigabyte E251-U70 User Manual Download Page 31 | Manualshive

Page: 31 / 111

Gigabyte E251-U70 User Manual Download Page 31

- 23 -

System Hardware Installation

3-6 Installing the GPU Card

Before you install the GPU card:

Voltages can be present within the server whenever an AC power source is connected. This

voltage is present even when the main power switch is in the off position. Ensure that the system
is powered down and all power sources have been disconnected from the server prior to installing
a GPU card. Make sure the system is not turned on or connected to AC power.

Failure to observe these warnings could result in personal injury or damage to the equipment.

Follow these instructions to install the GPU card:

1. Lift up the GPU card cage.
2. Remove the two screws securing the GPU card slot covers and remove the GPU slot covers.

3. Insert the GPU card into the selected slot. Make sure the GPU card is properly seated.

4. Install the two screws to secure the GPU card in place.

5. Install the three screws to secure the GPU card bracket in place.

1

2

3

«
...
29
30
31
32
33
...
»

Summary of Contents for E251-U70
















































































































Reviews:

No comments