GiBiDi F12E, Instructions For Installation Manual

Page: 9 / 32

PROFESSIONAL AUTOMATIC SYSTEM FOR GATES AND GARAGEDOORS English
9
This function allows reducing the pause time to only 4 seconds from inter vention and subsequent freeing of the PHOTOCELLS.
To enable the function, proceed as follows: during
time programming ( step 5 ) when the gate is in pause, black out the PHOTOCELLS for
at least three seconds . The flashlight star ts flashing to signal that the function has been stored. Free the PHOTOCELLS, wait for the
desired pause time and finish the time programming phase as normal. To disable the function, repeat the programming procedure without
blacking out the PHOTOCELLS.
FAST CLOSING FUNCTION
( run time, pause time)
Before proceeding with time programming, the control unit must be set for control of only one motor.
1) GATE CLOSED: set DIP5 to ON.
Press the button P1: the LED DL1 flashes twice (
pressing it again, it would flash once only to indicate double swing gate setting ).
Program the times respecting the same logic described above (steps 2, 3, 5, 6, 7, 8).
TIME PROGRAMMING
– single swing gate
For the flashlight to come on intermittently also during the pause time, press the second key of the remote control (previously learned)
during step 5 of time programming .
CONTROLLING THE FLASHLIGHT IN PAUSE TIME
(only if using the RADIO MODULE code AU01780)
If the radio module code AU01780 is used on the control unit, the signal transmitted is directly decoded by the control unit which is able
to decode rolling-code signals at a frequency of 433.92MHz.
For self-learning of the remote controls and complete memor y reset refer to the following:
Code learning (max. 200)
When powering the control unit the first time, the LED DL1 emits a brief flash.
Press the button P1 : the LED DL1 comes on fixed to indicate that the receiver is ready to learn a code.
Press a key of the transmitter (Key 2 only for PEDESTRIAN START): the LED DL1 flashes once to indicate that the code has been stored.
The button P1 does not have to be pressed again to store other remote controls one after the other.
When the LED DL1 goes off, it indicates that the system has exited the learning phase and is ready to function regularly.
Total memory reset
To delete all the codes stored, press the button P1
(the LED DL1 comes on) and hold it down until the LED DL1 goes off.
When the button is released, the LED flashes once to signal that the code memor y is empty.
RADIO MODULE
Before powering the control unit:
- Check proper setting of the dip switches.
- Check the electrical connections. Improper connections may irreversibly damage the control unit or present a hazard to the operator or the user.
FINAL CHECKS AND TESTING
- Check that the red LEDs (DL3, DL 4) are normally on and that the yellow LED (DL2) is off.
- Check that any detection devices connected to terminals 1-4 function properly
- Check that the gate is closed and that the motors are ready for operation.
- Remove any obstacles within the range of action of the gate.
POWER THE DEVICE
IMPORTANT:
If using another type of receiver, refer to the relevant instructions.
The manufacturer cannot be held responsible for damage caused by improper and/or irrational use.
Gi.Bi.Di. reser ves the right to make modifications at any time and without prior notice in order to improve the product.
TROUBLESHOOTING
The operator does not open or reclose
Check that the red LEDs are on and the yellow one off.
Connect the STOP input (terminals 2-4) to an NC button or jumper it.
Connect the START input (terminals 3-4) to an NO button.
FAULT POSSIBLE CAUSES and SOLUTIONS
The transmitter has little range
Check that the antenna has been positioned properly (braid terminal 15, signal terminal 16,
for control units code AS04330).
If a plug-in receiver is used (code AU01710), the antenna must be connected to the terminals
on the receiver.
Check that there are no sources of disturbance in the vicinity, which limit the range.
The PHOTOCELLS do not work
DIP6 ON. Set DIP6 to OFF and check that the LED DL4 goes off when the photocells are
blacked out.
Pressing the 2nd key of the TX the
pedestrian gate is not activated The second channel of the transmitter has not been learned previously.
Per form the learning procedure of the second channel.
WARNINGS
When wiring or inser ting the RADIO MODULE, the control unit must not be powered.
The control unit must be used strictly following the instructions provided by the manufacturer on pain of for feiture of the guarantee.
Installation and/or maintenance must be carried out by qualified personnel in compliance with the provisions of the laws in force.
Warning:
Before carrying out any operation (installation or maintenance) ensure that the power has been cut !!