background image

BLIZZARD 400-800 C ENC 

23 

532104 - Rev.A

2.5

1

2

 4 4

1

2

2.5

 4 3

3.6

3.6

2.5

Tr

ansla

tion of the orig

inal instruc

tions

ENGLISH

7.3  INSTALLATION OF THE LIMIT SWITCHES

RISKS

PERSONAL PROTECTIVE EQUIPMENT

1.  Move the gate to the closed position by hand.
2.  Position the closing magnetic limit switch on the rack (

 4 3

-1) 

and look for the point at which the FCC (closing limit switch) LED 

turns off.

3.  Mark the centre of the limit switch slots on the rack; manually 

open the gate by 1m.

4.  Drill a 3.6mm diameter hole in correspondence with the centre 

of the slots. Fasten the limit switch using two 3.9x16 self-tapping 

screws and two washers (supplied) (

 4 3

-2).

5.  Manually move the gate back into its stop position when closed 

and check that the FCC (closing limit switch) LED turns off. Other-

wise, adjust the position of the limit switch using the slots.

6.  Move the gate to the open position by hand.
7.  Position the opening magnetic limit switch on the rack (

 4 4

-

1) and look for the point at which the FCA (opening limit switch) 

LED turns off.

8.  Mark the centre of the limit switch slots on the rack; manually 

close the gate by 1m.

9.  Drill a 3.6mm diameter hole in correspondence with the centre 

of the slots. Fasten the limit switch using two 3.9x16 self-tapping 

screws and two washers (supplied) (

 4 4

-2).

10. Manually move the gate to its open position and check that the 

FCA (opening limit switch) LED turns off. Otherwise, adjust the 

position of the limit switch using the slots.

7.4  PROGRAMMING

The electronic board contains two Programming menus: Basic and 

Advanced.

L

i

To save the modifications made to the programming, scroll through the 

menu until you reach the 

St

 function leaving value 

unchanged 

If the mains power supply fails before the modifications are saved, all 

the modifications will be lost.
To reset the default values, set function 

dF

=

Y

 and save the modifica-

tions (

St

=

Y

).

BASIC PROGRAMMING

1.  To access the menu, press and hold down button 

F

: the display 

shows the first function (

dF

).

L

i

The display continues to show the name of the function as long as 

button 

F

 remains pressed.

2.  Release button 

F

: the display shows the value of the function.

3.  Press the 

+

 or 

-

 buttons to modify the value of the function.

4.  Press and hold down button 

F

 to go to the next function.

ADVANCED PROGRAMMING

1.  To access the menu, press and hold down button F and then press 

the 

+

 button: the display shows the first function (

PF

).

2.  Release the 

+

 button whilst keeping button 

F

 pressed.

L

i

The display continues to show the name of the function as long as 

button 

F

 remains pressed.

3.  Release button 

F

: the display shows the value of the function.

4.  Press the 

+

 or 

-

 buttons to modify the value of the function.

5.  Press and hold down button 

F

 to go to the next function.

Summary of Contents for BLIZZARD 400 C ENC



































Reviews: