manualshive.com logo in svg

gefran ADV200-...-DC Series, Quick Start Up Manual, Specification And Installation

Share
Download
gefran ADV200-...-DC Series Quick Start Up Manual, Specification And Installation Download Page 71

   

ADV200 • Quick start up guide - Specification and installation 

71

menu, PAR: 884) and 

Mpot down src 

parameter (PAR: 886) parameters respec-

tively to increase and decrease the reference using selection list L_DIGSEL2. 
Set the motor potentiometer ramps using 

Mpot acceleration 

(PAR: 872) and 

Mpot deceleration 

parameters (PAR: 874).

• Jog

Finally, for Jog mode, select the control terminal in the

 Jog cmd + src

 parameter 

(09 - JOG FUNCTION menu, PAR: 916), using a signal from selection list L_DIG-
SEL2. 
The Jog speed must be written in the 

Jog setpoint 

parameter (PAR: 910), while 

the acceleration and deceleration ramps can be set, respectively, in 

Jog accelera-

tion 

(PAR: 912) and 

Jog deceleration 

parameters (PAR: 914).

• Speed limits

After selecting the reference, set the speed limits in the following parameters (05 - 
REFERENCES menu):
-  

Full scale speed

 (PAR: 680). Setting of the maximum motor speed, which 

usually coincides with the rated speed indicated on the motor data plate.

-  

Speed ref top lim 

(PAR: 670). Upper speed limit: the maximum setting is 

200% of the 

Full scale speed

.

-  

Speed ref bottom lim 

(PAR: 672). Lower speed limit: the maximum setting is 

-200% of the 

Full scale speed

.

-  

Overspeed threshold 

(24 - ALARM CONFIG menu, PAR: 4540). Overspeed 

alarm limit.

• Input and Output terminals

The default setting of the input terminals is as follows:

- Terminal  7  

Digital input E   

Enable

- Terminal  8  

Digital input 1   

FR forward src, PAR 1042

- Terminal  9 

Digital input  2   

FR reverse src, PAR 1044

- Terminal  10  

Digital input  3   

Multi ref sel 0 src

- Terminal  11  

Digital input  4    

Multi ref sel 1 src

- Terminal  12  

Digital input  5    

Fault reset src

- Terminal  S3  

+ 24V OUT 

 

I/O supply

The default con

fi

 guration of the terminals dedicated to digital outputs are as fol-

lows:

- Terminal  R14  

Digital output 1  

Drive OK (Relay 1)

- Terminal  R11 

COM Digital output 1 

Common digital output 1 (Relay 1)

- Terminal  R24  

Digital output 2  

Drive ready (Relay 2)

- Terminal  R21  

COM Digital output 2 

Common digital output 2 (Relay 2)

- Terminal  13  

Digital output 3  

Speed is 0 delay

- Terminal  IC1  

COM Digital output 3/4 

Common ref. for digital outputs 3 / 4

- Terminal  14  

Digital output 4  

Ref is 0 delay

- Terminal  IS1  

PS Digital output 3/4 

Digital outputs 3 / 4 power supply

Signals for the digital outputs can be programmed using the 

Digital output 1...4 

src 

parameters (13 - DIGITAL OUTPUTS menu, PAR: from 1310 to 1316) using 

the settings in the L_DIGSEL1 selection list.

The drive also includes two analog outputs which are not factory-set. These 
outputs must be enabled by setting 

Analog out 1 src

 (15 - ANALOG OUTPUTS 

menu, PAR: 1800) and 

Analog out 2 src 

parameters (PAR: 1802) with a signal 

selected from selection list L_ANOUT. 

Summary of Contents for ADV200-...-DC Series














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands