manualshive.com logo in svg

gefran ADV200-...-DC Series, Quick Start Up Manual, Specification And Installation

Share
Download
gefran ADV200-...-DC Series Quick Start Up Manual, Specification And Installation Download Page 166

 

166

 

ADV200 • Quick start up guide - Specification and installation

Appendix 1 - Parallel connection (400 ... 1000kW sizes)

A 1.1 Introduction

To obtain a drive of more than 355 kW connect a number of single units of be-
tween 200 kW and 355 kW in parallel.
A parallel connection of several drives basically consists of one MASTER unit and 
one or more SLAVE units. 

Power

code

Description  (Designation)

Power

code

Description  (Designation)

400kW

S9O25M

ADV-72000-KXX-4-MS 04 -SI

900kW

S9O27M1

ADV-731500-KXX-4-MS 09 -SI

S9O25S

ADV-72000-XXX-4-SL

S9O27S

ADV-731500-XXX-4-SL

500kW

S9O26M

ADV-72500-KXX-4-MS 05 -SI

S9O27S

ADV-731500-XXX-4-SL

S9O26S

ADV-72500-XXX-4-SL

1000kW

S9O28M1

ADV-735500-KXX-4-MS 10-SI

630kW

S9O27M

ADV-731500-KXX-4-MS 06 -SI

S9O28S

ADV-735500-XXX-4-SL

S9O27S

ADV-731500-XXX-4-SL

S9O28S

ADV-735500-XXX-4-SL

710kW

S9O28M

ADV-735500-KXX-4-MS 07 -SI

S9O28S

ADV-735500-XXX-4-SL

Master unit

this is the only one to have the regulation card and keypad. It differs from the 
standard single unit in that the power section control card (INT-P-ADV) is recon-

fi

 gured to function as MASTER and includes one or more MASTER - SLAVE (INT-

SLAVE) interface cards, one card for each slave that is connected.
The MASTER - SLAVE interface is achieved via a speci

fi

 c signal cable included in 

the SLAVE drive packaging.

Slave unit

It differs from the standard single unit in that it has a dedicated power section 
control card (INT-P-ADV) and there is no regulation card or keypad.

INT-P-ADV-MASTER card

The INT-P-ADV-MASTER card provided with one or more INT-SLAVE cards, acts 
as the interface between the R-ADV regulation card and the power section of the 
master unit and all the slave units. It also performs the following functions:
• 

current signal scaling (via dip switch, factory-set)

• 

hardware dead time compensation

• 

alarm signal management (including local diagnostics via LED)

• 

temperature signal management.

INT-P-ADV-SLAVE card

The INT-P-ADV-SLAVE card interfaces between the power section of the slave 
unit and the master unit. It also performs the following functions:
• 

alarm signal management (including local diagnostics via LED)

• 

temperature signal management.

INT-SLAVE card

The INT-SLAVE interface card manages communication between a master unit 
and a slave unit. 
The INT-SLAVE cards are mounted on the master unit, their number correspond-
ing to that of the slaves that are connected (max. 4 slaves).
The INT-SLAVE card is factory-set.

Summary of Contents for ADV200-...-DC Series














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands