manualshive.com logo in svg

gefran ADV200-...-DC Series, Quick Start Up Manual, Specification And Installation

Share
Download
gefran ADV200-...-DC Series Quick Start Up Manual, Specification And Installation Download Page 67

   

ADV200 • Quick start up guide - Specification and installation 

67

 Step 7 - Speed tests

In this step the basic settings in order to perform a functional test of the drive-
motor system are described. This functional test uses 

factory settings as far 

as the analog and digital commands of the drive are concerned

. The preset 

regulation mode is V/f. 

• Basic connections for the speed test

S1+

1

S1-

C1

C2

C3

+1

0

V

0

V1

0

Analog input 1

COM-DI

0

V 24V

- 1

0

V

S3

9

7

8

FR reverse src

Enable

FR forward src

+24V OUT

Dig.inp 1

Dig.inp 2

Dig.inp E

2

+

-

R1

(2 ...

5

kohm)

After making the connections described in the previous section, proceed as fol-
lows to start the motor rotating:
1.  Make sure the analog signal or potentiometer are set to the minimum value.
2. Close 

the 

Enable

 contact (terminals S3 – 7)

3. Close 

the 

FR forward src (PAR 1042) 

contact, terminals S3 – 8. The drive 

starts magnetizing the motor

4.  Increase the reference signal gradually using the potentiometer or analog 

signal

5.  If the motor rotates anti-clockwise with the 

FR forward src (PAR 1042)

  com-

mand and a positive analog reference, stop the drive, disconnect the power 
supply and invert two phases between U, V and W.

6. Press 

the 

DISP

  key to check that the voltage, current and output frequency 

values are correct in relation to the type of motor and the set speed reference 
value.

7.  If all the parameters are correct, increase the analog reference to the full scale 

value and check that the output voltage is the same as that on the motor data 
plate, that the current is approximately equal to the magnetizing current (for 
a standard asynchronous motor this is usually between 25% and 40% of the 
rated current) and that the output frequency is 50 Hz.

8.  If the motor does not reach its maximum speed, self-tuning of the analog input 

may be necessary‘: set the input signal to its maximum value and set the 

An 

inp 1 gain tune 

parameter (PAR: 1508) to 1.

9.  If the motor still rotates with a reference of zero, eliminate the condition by 

self-tuning the analog input offset: set the input signal to its minimum value 
and set 1 for 

An inp 1 offset tune 

(PAR: 1506).

10. To reverse the direction of rotation, keep closed the 

FR forward src (PAR 

Summary of Contents for ADV200-...-DC Series














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands