manualshive.com logo in svg

gefran ADV200-...-DC Series, Quick Start Up Manual, Specification And Installation

Share
Download
gefran ADV200-...-DC Series Quick Start Up Manual, Specification And Installation Download Page 167

   

ADV200 • Quick start up guide - Specification and installation 

167

A 1.2 MS-SL interface cable wiring sizes 400...710 kW

Fit the ADV200 MASTER and SLAVE inverters inside the electrical panel. Connect 
all the power section cables and connect the signal cable for interfacing between 
the 2 drives.

The cable (code 8S860B) for connecting 2 drives is one metre long and has two 
quick coupling male MDR connectors at the ends.

ADV-...-MS-..

ADV-...-SL

INT

-P-ADV SLA

VE card

INT

-SLA

VE card

XSL connector

J4 connector

INT

-P-ADV MASTER card

1.

2.

3.

4.

5.

Wiring instructions:
1. 

Connect one of the 2 ends of the interface cable to the XSL connector of the 
INT-P-ADV-SLAVE card. 

2. 

Secure the cable using the speci

fi

 c clamp.

3. 

Connect the other end of the cable to connector J4 of the INT-SLAVE card 
mounted on the INT-P-ADV-MASTER card of the MASTER drive.

4. 

Secure the cable in the relative clamp

5. 

To prevent the interface cable from coming into contact with the power termi-
nals, fold the excess length of cable inside the SLAVE drive as shown in the 

fi

 gure and secure it using the speci

fi

 c cable clamps.

Summary of Contents for ADV200-...-DC Series














































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands