gefran ADV200-...-DC Series Quick Start Up Manual, Specification And Installation Download Page 53

Page: 53 / 173

ADV200 • Quick start up guide - Specification and installation

6.5 Con

guration of the display

6.5.1 Language selection

Menu 04 DRIVE CONFIG, parameter 04.15

Language select

, PAR: 578,

default=English.
Used to set one of the languages available : English, Italian, Francais, Deutsch,
Polish, Romanian, Russian, Turkish and Portuguese.

T+

T-

LOC

ILim

0 4 . 1 5

PA R :

5 7 8

a e se

ect

T+

T-

LOC

ILim

0 4 . 1 5

PA R :

5 7 8

a e se

ect

ano

T+

T-

LOC

ILim

0 4 . 1 5

PA R :

5 7 8

a e se

ect

T+

T-

LOC

ILi

ONITO

02 D

IVE INFO

03 STA

WIZA

04 D

IVE CONFI

X 3

T+

T-

LOC

ILi

ONITO

02 D

IVE INFO

03 STA

WIZA

04 D

IVE CONFI

Note !

To access the Cyrillic font:

: 1) press the E key and hold it down while you switch the drive on, 2)

select the required font using the

▲

and

▼

keys, 3) press E to confirm and return to normal operating

mode.

6.5.2 Selection of Easy / Export mode

T+

T-

ILi

4 .

0 3

5 5

Access mode

Eas

Value

T+

T-

ILim

02 D

RIVE I

03 S

TARTUP WIZAR

RIVE

CON

FIG

T+

T-

ILi

4 .

0 3

5 5

Access mode

Ex ert

Value

Menu 04 DRIVE CONFIG, parameter 04.03

Access mode

, PAR: 570.

Makes it possible to con

gure two methods of access :

Easy

(default) only the main parameters are displayed, see

paragraph 8.2

List of parameters.

Expert

for advanced users, all the parameters are displayed, see

paragraph

8.2

List of parameters.

6.5.3 Startup display

Note !

This parameter is visible only in

Expert

mode (see

paragraph 6.5.2

Menu 04 DRIVE CONFIG, parameter 04.13

Startup display

, PAR : 574.

Used to set the parameter that will be displayed automatically at drive power-on.
Entering the value -1 (default), the function is disabled and the main menu is
displayed at power-on. Set to 0 to show the display menu.

6.5.4 Back-lighting of the display

Note !

This parameter is visible only in

Expert

mode (see

paragraph 6.5.2

Summary of Contents for ADV200-...-DC Series














































































































































































Search results

Summary of Contents for ADV200-...-DC Series

Reviews:

Brands by name

Popular brands

gefran ADV200-...-DC Series, Quick Start Up Manual, Specification And Installation

Search results

Summary of Contents for ADV200-...-DC Series

Reviews:

Brands by name

Popular brands