GE PanaFlow MV80 User Manual Download

Page: 136 / 164

Chapter 5. Troubleshooting and Repair

124

PanaFlow™ MV80 & MV82 User’s Manual

5.6 Pressure Sensor Replacement (Series MV80 Only)

For local mounted electronics, remove the electronics stack as previously described. For remote mount
electronics, remove all wires and sensor connectors from the remote feed through board in the junction box at
the meter.

Loosen the three set screws at the center of the adapter between the meter and the enclosure.

Remove the top half of the adapter to expose the pressure transducer.

Remove the transducer and replace it with the new one using appropriate thread sealant.

Reassemble in reverse order.

5.7 Returning Equipment to the Factory

Before returning any PanaFlow MV flowmeter to the factory, you must request a Return Material Authorization (

RMA

)

number. To obtain an

RMA

number and the correct shipping address, contact

GE Customer Service

using the

information on the back cover of this manual.

IMPORTANT:

When contacting Customer Service, be sure to have the meter serial number and model code available.

When requesting further troubleshooting guidance, please record the values in the tables provided in

“Troubleshooting

the Flowmeter” on page 116

and have this information available.

Summary of Contents for PanaFlow MV80





































































































































































Search results

Summary of Contents for PanaFlow MV80

Reviews:

Related manuals for PanaFlow MV80

Brands by name

Popular brands

GE PanaFlow MV80, User Manual

Search results

Summary of Contents for PanaFlow MV80

Reviews:

Related manuals for PanaFlow MV80

Brands by name

Popular brands