GE PanaFlow MV80 User Manual Download

Page: 36 / 164

Chapter 2. Installation

PanaFlow™ MV80 & MV82 User’s Manual

2.3.3 Installing Flowmeters with a Packing Gland Connection (cont.)

Example 2 - NPT Style Meters:

In this example, the length of thread engagement on the NPT style meters must also subtracted in the equation shown in

Figure 13 on page 23

. The length of the threaded portion of the NPT meter is 1.18 inches. Measure the threaded

portion still visible after the installation and subtract that amount from 1.18 inches. This gives you the thread
engagement length. If this cannot be measured, use 0.55 inch for this amount.

•

F = 12 inches

•

R = 5 inches

•

t = 0.438 inches

•

thread engagement = 1.18 inches - visible thread length (or 0.55 inches nominal value)

For this example, the equation yields an insertion length of 15.54 inches.

2.3.4 Insertion Procedure for Flowmeters with Permanent Insertion Tool

Refer to

Figure 14

below, and follow the instructions on the next page.

Figure 14: Flowmeter with Permanent Insertion Tool

Flow

Sensor Head

Stem Housing

Packing Gland Nuts

Stem

Sensor Alignment

Pointer

Stem Lock Bolt

(center)

Upper Retractor Bracket

Depth Marker Arrow

Stanchion

Scribe Mark

Permanent

Insertion Tool

Summary of Contents for PanaFlow MV80





































































































































































Search results

Summary of Contents for PanaFlow MV80

Reviews:

Related manuals for PanaFlow MV80

Brands by name

Popular brands

GE PanaFlow MV80, User Manual

Search results

Summary of Contents for PanaFlow MV80

Reviews:

Related manuals for PanaFlow MV80

Brands by name

Popular brands