GE ImageQuant LAS 4000 Original Instructions Manual Download Page 35

Page: 35 / 86

3.5.2 Connecting the camera head to the computer

Connect the USB cable from the USB connector of the ImageQuant LAS 4000 camera head to one of
the USB ports of the computer.

Analysis PC (Optional)

Instrument

Note:

• Use the USB cable supplied with the equipment.

• Do not connect via a USB hub.

• Do not use other USB equipment on the PC while ImageQuant LAS 4000 is in use.

This may result in the loss of image data.

3.5.3 Installing the lens

This section describes how to install the LAS High Sens. lens. For instructions on installing the wide
view lens, refer to the ImageQuant LAS 4000 User Manual.

1 Ensure that the ImageQuant LAS 4000 and the PC are connected. Turn on the instrument and the

PC and start the ImageQuant LAS 4000 Control Software.

2 Select Lens Exchange... in the Option menu.

A message is displayed.

Click OK.

Getting Started with ImageQuant LAS 4000 28-9607-59 AB

3 Installation

3.5 Installation of hardware

3.5.2 Connecting the camera head to the computer

Summary of Contents for ImageQuant LAS 4000























































































Search results

Summary of Contents for ImageQuant LAS 4000

Reviews:

Related manuals for ImageQuant LAS 4000

Brands by name

Popular brands

GE ImageQuant LAS 4000, Original Instructions Manual

Search results

Summary of Contents for ImageQuant LAS 4000

Reviews:

Related manuals for ImageQuant LAS 4000

Brands by name

Popular brands