GE FHV5SGWW Service Manual Download

Page: 47 / 61

Freezer Model:FHV5SGWW/FHV7SGWW

４６

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

(1) In semi-sound eliminating room or in sound eliminating room without

sound wave reflection.

(2) Put freezer onto 5-10mm elastic cushion.

(3) Freezer must be empty and running at least 30 minutes before

measuring. If normal stop happens, please make the measurement 3

minutes after freezer starting again.

(4) 4 measuring positions are required, they are 1m away from freezer at

front, back, front left, front right respectively. The height is 1/2 of freezer;

the instrument is accurate sound level meter (A weighted).

12.6.12 What

’

s the different between national noise

standard 52dB(A) and ministry of light industry standard
42dB?

Answer: The noise of 52dB(A) in national standard is the sound power level.

Under the measuring conditions stipulated in national standard, measure

the freezer noise at four points, take the average of indicated reading at

greater noise situation, calculate the arithmetic average value of the four

points. This value is the average sound pressure level of noise, the

calculation formula is:

=(L

-2)+10LgS

where: L

—

sound power level, dB

-average sound pressure level of measuring surface, dB

—

the envelope area of measuring surface, m

PDF created with pdfFactory trial version

www.pdffactory.com

Summary of Contents for FHV5SGWW






























































Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands

GE FHV5SGWW, Service Manual

Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands