GE FHV5SGWW Service Manual Download

Page: 9 / 61

Freezer Model:FHV5SGWW/FHV7SGWW

８

INSTALLATION AND ACCESSORY PARTS

Installation and Accessory Parts

Unpacking Your Freezer

1.Remove all packaging material; this includes the foam base and all adhesive

tape holding the freezer accessories inside and outside.

2.Inspect and remove any remains of packing, tape or printed materials before

powering on the freezer.

Adjusting Your Freezer

1.Your freezer is designed for freestanding installation only. It should not be

recessed or built-in.

2.Place the freezer on a floor strong enough to support it fully loaded.

3.When moving the freezer, never tilt it more than a 45-degree angle. This could

damage the compressor and the sealed system.

4.If the freezer is tilted let it stand in an upright position for at least 24 hours prior

to plugging. This is to allow the refrigerant to settle.

Proper Air Circulation

To assure your freezer works at the maximum efficiency it was designed for,

you should install it in a location where there is proper air circulation,

Plumbing and electrical connections.

The following are recommended clearances around the freezer:

Sides

…………

..2

”

(50mm)

Top.

……………

”

(50mm)

Back

…………

..2

”

(50mm)

PDF created with pdfFactory trial version

www.pdffactory.com

Summary of Contents for FHV5SGWW






























































Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands

GE FHV5SGWW, Service Manual

Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands