GE FHV5SGWW Service Manual Download | Manualshive

Page: 35 / 61

background image

Freezer Model:FHV5SGWW/FHV7SGWW

３４

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

12.4.2 Notice for use

(1) The freezer should level, the tilting angle when moving shall not be

greater than 45

°

, so that the sliding door could not move out from its

guiding slot and other accident will not happen.

(2) The clearance between freezer and other objects should be more than

30 cm for ventilation and heat radiation.

(3) Please don

’

t leave the freezer at humid or corrosive gas area.

(4) Freezer should be placed at a place with proper ventilation, away from

heat source, and avoiding direct sunlight.

At the first application, please wait some time for operation (in summer 6

hours, in winter, 4 hours), when the temperature inside the freezer has

(5) reached to -15

℃

and below, then you can put food in. If food is put in

too early, it may get damaged, as the temperature is still high.

(6) Do not over pack refrigerator.

(7) Place food by reasonable sorts, try to power open door frequency and

time so as to reduce the loss of refrigeration and reduce consumption.

(8) There are four wheels at the bottom of freezer, but it can only be used

for short distance and on level road movement. If it is required to move

frequently, please put the freezer onto a strong trolley base.

PDF created with pdfFactory trial version

www.pdffactory.com

«
...
33
34
35
36
37
...
»

Summary of Contents for FHV5SGWW






























































Reviews:

No comments

Related manuals for FHV5SGWW

Brand: True Pages: 2

Snowflake SBU 15 H

Brand: Hoshizaki Pages: 32

Brand: Haier Pages: 16

Brand: Haier Pages: 11

Brand: Haier Pages: 8

Brand: AEG Pages: 24

Brand: AEG Pages: 40

Brand: AEG Pages: 20

Brand: AEG Pages: 60

Brand: AEG Pages: 48

Brand: AEG Pages: 44

Brand: AEG Pages: 36

Brand: AEG Pages: 44

Brand: AEG Pages: 20

Brand: AEG Pages: 16

Brand: AEG Pages: 20

Brand: AEG Pages: 72

Brand: AEG Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands