GE FHV5SGWW Service Manual Download

Page: 44 / 61

Freezer Model:FHV5SGWW/FHV7SGWW

４３

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

12.6.4 Gas flowing sound

At operation of compressor, it breathes in and exhausts out gas

continuously. When liquid refrigerant flows through capillary, there will be

gas jet and makes sound of gas flowing. This is normal sound and may be

different for various freezers as compressors and evaporators used are

different.

12.6.5 Why there is sudden

“

cluck

”

sound or

“

pattering

”

sound from freezer?

Answer: This is the sound of expanding with heat and contracting with cold

of condenser and evaporator, or the sound of ice at evaporator surface

because of sudden heat or cold. This sound may occur at the following

situations:

(1) Newly bought freezer, the internal stress of materials has not been

eliminated. With time going on, the stress of materials will disappear

and it is less possible to make this sound.

(2) Temperature in the freezer is not uniform just after frost melting.

(3) When open door and take out food, the evaporator feels hot suddenly.

(4) Temperature changes greatly of condenser and evaporator several

minutes after starting or stopping of freezer.

Expand with heat and contract with cold is natural law, and this sound is

normal.

PDF created with pdfFactory trial version

www.pdffactory.com

Summary of Contents for FHV5SGWW






























































Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands

GE FHV5SGWW, Service Manual

Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands