GE FHV5SGWW Service Manual Download | Manualshive

Page: 29 / 61

background image

Freezer Model:FHV5SGWW/FHV7SGWW

２８

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

12.1.13 Procedure for temperature controller change

(1) Switch off power.

(2) Remove side protection cover.

(3) Unscrew fastening nut.

(4) Hold the base end of temperature sensing tube and the controller, pull

out downward.

(5) Change with new temperature controller.

12.2 Common freezer problems

12.2.1 Freezer cannot be started

When switching on power, the freezer cannot be started. Determine first

that the failure is caused by inside or outside factors. The factors may be:

(1) Outside factors

①

The fuse is burned, or the contact of plug and socket is not well, or the

voltage is too low.

②

The knob of temperature controller is set to off position.

(2) In side factors

①

Electrical problem of freezer (normally caused by connection terminals

coming off or not in good contact).

②

Temperature controller out of order (contact point are burned or switch

element is damaged, etc.).

③

The start capacitor is bad.

PDF created with pdfFactory trial version

www.pdffactory.com

«
...
27
28
29
30
31
...
»

Summary of Contents for FHV5SGWW






























































Reviews:

No comments

Related manuals for FHV5SGWW

Brand: Haier Pages: 2

Brand: Galanz Pages: 15

Brand: elvita Pages: 88

Brand: Jula Pages: 22

Brand: Electrolux Pages: 24

Brand: Electrolux Pages: 44

Brand: Panasonic Pages: 33

Brand: Panasonic Pages: 32

Brand: Panasonic Pages: 35

Brand: Panasonic Pages: 35

Brand: Panasonic Pages: 36

MDF-C8V1 Series

Brand: Panasonic Pages: 41

Brand: Panasonic Pages: 45

MDF-DC500VX Series

Brand: Panasonic Pages: 64

MDF- DU900VC Series

Brand: Panasonic Pages: 63

Brand: AEG Pages: 64

Brand: Modena Pages: 23

Brand: Elkay Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands