GE FHV5SGWW Service Manual Download

Page: 55 / 61

Freezer Model:FHV5SGWW/FHV7SGWW

５４

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

12.8.2.7 Test method of refrigeration performance

(1) 4 or 6 freezers can be tested simultaneously at the test room. The

material of enclosure structure of test room is made up of 10mm thick

polyurethane or polystyrene, which has good insulation. There are air

re-treatment motor sets in the test room. Air comes into the room from

the ceiling of porous plate with uniform pressure, so as to assure

airflow speed in the room not over 0.25m/s and thus keep the room

temperature uniformly.

The temperature of test room is adjustable within the range of 10-43

℃

(2) Temperature requirements for different climate freezers please refer to

table 6-1.

Each test point shall keep the stipulated environment temperature, the

fluctuation range is +-0.5K. Within the range of 2m heights away from the

test platform, the vertical temperature gradient shall not exceed 2K/m.

Table 6-1 Different climate sorts for freezers

Climate types

Symbols

Suitable
temperature (

℃

)

Measuring
temperature (

℃

)

Sub-temperate
zone
Temperate zone
Sub-tropical
zone
Tropical zone

SN
N
ST
T

10-32
16-32
18-38
18-43

25
25
25
32

(3) Environmental humidity: normally the relative humidity is 45-75%.

PDF created with pdfFactory trial version

www.pdffactory.com

Summary of Contents for FHV5SGWW






























































Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands

GE FHV5SGWW, Service Manual

Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands