GE FHV5SGWW Service Manual Download | Manualshive

Page: 22 / 61

background image

Freezer Model:FHV5SGWW/FHV7SGWW

２１

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

(3) The cover temperature of The evaporator can be as low as

-30

℃

it will feel sticky when touching. If you

’

d like to touch,

please move your hand over it quickly, otherwise your hand will

be stuck.

(4) At normal operation of freezer, the temperature of filter dryer

cover is similar to room temperature, only a little warmer. If the

cover temperature is much higher or lower than that of

environment, and there is frost, there must be problem with the

refrigeration system.

Touching the above mentioned parts, if there is big temperature

difference compared with normal, there must be problem and

further decision should be made.

12.1.6 System noise repair

Normally there are two kinds of freezer noise, one is the natural

noise of compressor and fan, and the other is the resonance

noise or structural noise. The natural noise of compressor and

fan is controlled within a standard range, if the range is exceeded,

the compressor or fan needs to be repaired or changed. The

resonance or structural noise can be handled as follows:

PDF created with pdfFactory trial version

www.pdffactory.com

«
...
20
21
22
23
24
...
»

Summary of Contents for FHV5SGWW






























































Reviews:

No comments

Related manuals for FHV5SGWW

Brand: True Pages: 2

Brand: CombiSteel Pages: 48

Brand: Waeco Pages: 320

Brand: Kuppersbusch Pages: 11

Brand: Signature Pages: 58

Brand: Hanseatic Pages: 63

Brand: FRIGOGLASS Pages: 112

Brand: Beko Pages: 36

Brand: Beko Pages: 60

Brand: Sanyo Pages: 1

Brand: Sanyo Pages: 2

Brand: Sanyo Pages: 4

Brand: Sanyo Pages: 21

Brand: Sanyo Pages: 32

Brand: Sanyo Pages: 41

Brand: Sanyo Pages: 42

Brand: Whirlpool Pages: 1

Brand: Whirlpool Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands