GE FHV5SGWW Service Manual Download

Page: 54 / 61

Freezer Model:FHV5SGWW/FHV7SGWW

５３

MAINTENANCE SERVICE AND TROUBLE SHOOTING

Maintenance Service and Trouble Shooting

12.8.2.3 Electrical intensity

This test is to check the electrical intensity of live parts and all accessible

metal parts. The testing equipment is flashover and breakdown unit,

voltage is 1650V (50Hz) for 2s. At the test, there will not flashover and

breakdown occurring.

12.8.2.4 Ground resistor

Check the voltage drop between freezer ground connection point and

accessible metal parts, using AC power of load empty voltage not over 12V

and 10A current. Calculate the resistance according to the current and

voltage drop. Ground connection resistance shall not exceed 0.1 ohm.

12.8.2.5 Leakage of current

When testing, give 1.06 times rated voltage to the freezer, and make the test

at operation status. The test complies with GB4706.1-84, the leakage

current testing instrument is made in accordance with the stipulations. The

leakage current measured shall not exceed 1.5mA.

12.8.2.6 Noise test

This test is carried out at semi sound eliminating room. The freezer is put

to the geometrical center of room, on a 5-10mm thick elastic cushion. The

freezer should be empty when testing. Turn the knob of temperature

controller to middle or near to strong position and close the door. Test after

the freezer has running more than 30 minutes. The freezer noise power

level, 250L and below,

≤

52dB(A); 250L above

≤

55dB(A)

PDF created with pdfFactory trial version

www.pdffactory.com

Summary of Contents for FHV5SGWW






























































Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands

GE FHV5SGWW, Service Manual

Search results

Summary of Contents for FHV5SGWW

Reviews:

Related manuals for FHV5SGWW

Brands by name

Popular brands