manualshive.com logo in svg

GE eBike II Series, Service Manual

Share
Download
GE eBike II Series Service Manual Download Page 104

- 104 - 

eBike II, eBike II L, eBike II EL 

2018112-069 Rev. F

•  Place the special tool onto the power connector and 

unlatch the clamps by pressing the tool downwards.

•  Disconnect the power connector.

•  Disconnect the remote control cable connector the 

same way.

•  The other side of the tool is used to unlatch the 

connectors of the motor cables (marked 1, 2 and 3) by 
turning the connector (bayonet fixing) and pulling out. 

•  Loose the fixing screws of the motor control unit.

•  Assembly of the new control unit is performed in 

reverse order.

Hint

•  Do not interchange the motor connectors! 

(Cable and jacks are marked !)

•  Following the exchange of a motor or after any malfunc-

tion the control unit has to be initialised! 
 
To initialise the control unit, both motors have to be 
moved in defined end positions:: 
 
 - The motor for the supine angle has to be retracted  
   completely (supine horizontal) 
 
-The saddle motor have to be extended completely.

Summary of Contents for eBike II Series











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands