Menu 1, DGP status
This menu lists different types of information regarding settings,
DGP addresses to poll, inputs ranges, output ranges, current
consumption, etc. To view all data, enter the menu and press
ENTER to view the next item.
Menu 2, Input status
Shows the current status of all inputs that have been enabled and
the digital value of the status. The range that is available can be
viewed in the DGP Status. The input numbers used are related to
the address selected. See “Zone and output numbering”.
To view the status, enter the first input to view. The selected input
status is shown. Press MENU to view the previous or ENTER to view
the next input.
Menu 3, DGP settings
Menu 3 provides for some additional settings related directly to
the DGP functionality. Use the MENU key to change the settings.
Use ENTER to accept the settings and move to the next item.
1. DGP configuration
: selects the number of inputs and outputs
used. Available settings:
1 DGP Address
Allows for max 16 inputs/outputs to be connected.
Shows as “DGP: n” where n is the selected DGP
address in menu 1, DGP status (Default setting)
1 DGP+exp
Allows for max 32 inputs/16 outputs to be
connected. Shows as “DGP: n + exp” where n is the
selected DGP address in menu 1, DGP status.
2 DGP Addresses
Allows for max 32 inputs/outputs to be connected
but requires DGP polling to be enabled for the DGP
address and the DGP a 1. Shows as “DGP: n
+ m” where n is the selected DGP address and m is
the a 1 in menu 1, DGP status.
2. Battery load:
Select if the battery load resistor should be
enabled on output 8. It will follow the battery test and add an
additional 68
Ω
during the test. This option is required for
regulations (SKAFOR). Default is OFF.
3. Mains check:
Enable/disable mains check. Set to OFF in case no
mains power supply is used to avoid mains fail being reported.
Default is ON.
4. Static outputs:
Select whether to support static outputs (max 8)
or clocked outputs (max 32, depending on DGP configuration).
Default is Static outputs.
Menu 4, Factory reset
Use this menu to set all DGP configurations to default factory
settings.
Technical specifications
Mains power specifications
Mains Input Voltage (J17 – AC)
230 VAC
±
10%, 50Hz
±
10%
Current consumption at 230V~
360 mA
Main board supply voltage
23 VAC typical
Power supply specifications
Power supply voltage
13.8 VDC
±
5%
Power supply current
2.9 A max. at 13.8 VDC
±
5%
Auxiliary Power output* (J14)
13.8 VDC
±
5%
For current see table below
Battery Power output (J17 – BAT)
13.8 VDC
±
5%.
For current see table below
Battery Type and max. capacity
Lead acid rechargeable 2 x 25 Ah
12 V nom. (BS129)
Main board consumption
75 mA at 13.8 VDC
±
5%
* Maximum permanent current to power devices external to the control
equipment in the absence of alarm conditions.
Available Aux/Battery current based on backup
Time (h)
Battery capacity (Ah)
Approval
Grade
Discharge
Charge
Output
7.2 18 25 36 50
Current
(mA)
Incert 24 24 Aux 200 600 875 1200 1200
Battery 2525 2125 1850 1525 1525
EN
1&2 12 72 Aux
490 1300 1800 1800 1800
Battery 2235 1425 925 925 925
EN
3&4 60 24 Aux 40 220 330 500 550
Battery 2685 2500 2395 2225 2175
NF
&
A2P 36 30 Aux 110 360 550 850 1000
ΙΙ
Battery 2615 2350 2200 1875 1725
NF
&
A2P 72 30 Aux 20 150 230 380 580
ΙΙΙ
Battery 2700 2600 2500 2345 2100
VdS
30 24 Aux 150 500 700 1050 1100
B
Battery 2575 2225 2025 1675 1625
VdS
60 24 Aux 40 220 330 500 550
C
Battery 2685 2500 2395 2225 2175
General feature specifications
End of line resistor
(standard)
4.7 k
Ω
5% 0.25 W (2.2 k
Ω
or 10 k
Ω
)
Standard on board output
Ext. siren (J13 — S+/S
−
)
Electronic output
Rating: 1 A at 13.8 VDC
Housing dimensions
ATS1203: 370 x 475 x 160 mm
ATS1204: 460 x 475 x 160 mm
Colour Beige
Operating temperature
−
10 to +55°C (cer5 to 40°C)
Humidity 95%
noncondensing
IP protection grade
IP30
Fuses
F4
Auxiliary power &
siren
F2 A, 20x5
F5 Battery
F3
A,
20x5
*
Mains fuse
ATS1203: Slow T – 400 mA 20x5
ATS1203N/ATS1204(N): Fast F– 630 mA 20x5
* Mains fuse is part of the mains terminal block.
WARNING:
Before removing the mains fuse, mains power must be
disconnected!
P/N 1064130 • REV 3.0 • ISS 10MAR09
7 of 24
