GE ApexPro Operator'S Manual Download Page 85

Page: 85 / 218

Alarms

2001989-200E

ApexPro™

5-17

Printing alarm settings

A telemetry patient’s

Alarm Control

tab sheet can be printed, showing all current

alarm settings and limits. Click on the

Print

button in the main menu to start a

printout of the

Alarm Control

tab sheet.

The

Alarm Control

tab sheet prints at the Print Window location. For more

information about setting the Print Window location, refer to

Chapter 9

in this

manual.

NOTE

The

Alarm Control

tab sheet must be the front tab of the single patient viewer in

order to print it. Click on the

Alarm Control

tab to bring it to the front if

necessary.

Stop printing an alarm graph

You can stop the printing of an alarm graph from any in-unit CIC Pro center
displaying the alarming patient bed.

Stop printing to a laser printer

Complete the following procedure to stop printing all print jobs sent to the laser
printer:

From the multi-patient viewer, click

CIC Setup

CIC Defaults

. The

CIC

Defaults

window displays.

Under

Printer/Writer

, click

Cancel Print Jobs

for the printer you want to stop

printing to.

After making your selection, complete one of the following tasks from the

CIC

Defaults

window:

Click

to apply your changes and close the

CIC Defaults

window.

Click

Cancel

to cancel your changes and close the

CIC Defaults

window.

Click

Apply

to apply your changes without closing the

CIC Defaults

window.

Stop printing to a local digital writer

Complete the following procedure to stop printing the current print job sent to a local
digital writer:

Locate the digital writer.

Press the

(

Graph Stop

) button located on the front of the digital writer to

stop the print job.

Summary of Contents for ApexPro


























































































































































































































Search results

Summary of Contents for ApexPro

Reviews:

Related manuals for ApexPro

Brands by name

Popular brands

GE ApexPro, Operator'S Manual

Search results

Summary of Contents for ApexPro

Reviews:

Related manuals for ApexPro

Brands by name

Popular brands