GE ApexPro Operator'S Manual Download Page 81

Page: 81 / 218

Alarms

2001989-200E

ApexPro™

5-13

319E

Parameter limits

To change the unit defaults for

Parameter Limits and Alarm Levels,

use the

mouse to click in the

Low

High

field for the parameter you wish to edit. The

field is framed by a rectangle, and up and down arrow buttons appear in the field.

329A

To increase or decrease the limit by 5, click on the up or down arrow button.

To increase or decrease the limit in increments other than 5, use the keyboard to
enter a new limit value.

Once you have set the desired limit, click on the

Apply

button for the changes to

take effect.

NOTE

If you make only one change, you do not need to click on the

Apply

button.

The change will take effect automatically, and the

Apply

button will appear

dimmed.

If you are finished making changes to the

Telemetry Alarm Control Defaults

tab

sheet, click the

button.

Summary of Contents for ApexPro


























































































































































































































Search results

Summary of Contents for ApexPro

Reviews:

Related manuals for ApexPro

Brands by name

Popular brands

GE ApexPro, Operator'S Manual

Search results

Summary of Contents for ApexPro

Reviews:

Related manuals for ApexPro

Brands by name

Popular brands