GE ApexPro Operator'S Manual Download Page 110 | Manualshive

Page: 110 / 218

background image

7-2

ApexPro™

2001989-200E

Viewing real-time patient data

Real-time patient views

You can view real-time data for patients located in your care unit, and when
networked with other CIC Pro centers, you may also view real-time data for patients
located outside of your care unit.

The CIC Pro center allows you to view real-time patient data from two different
patient viewers. Each viewer provides a different level of data granularity:

Multi-patient viewer

Single patient viewer

CAUTION

TREATMENT — Do not treat a patient based solely on the alarm
messages and/or numerics presented via the connectivity device to
the monitor. You must verify the accuracy of the alarm message and/
or numerics at the peripheral device itself before initiating treatment.
Treatment should be based on the information presented at the
peripheral device.

Data synchronization

Information displayed on the ECG tab sheet is synchronized with the source
(transmitter) every two seconds. If differences are detected, the display is refreshed
with new patient data.

Multi-patient viewer

The multi-patient viewer displays a snapshot of real-time parameter data for a
maximum of 16 patients. You can do the following real-time tasks from the multi-
patient viewer:

View abbreviated real-time patient data.

View a snapshot of real-time

Graphic Trends

data for a maximum of two

different parameters.

See Configuring the real-time trend window on page 7-6.

Print parameter limits or waveform data for all patients in the care unit.

Printing parameter limits or waveforms for all in-unit patient beds on page 7-9.

View a single patient’s detailed real-time parameter data.

See Single patient

viewer on page 7-3.

View a single patient experiencing an alarm condition.

See Viewing in-unit

patients experiencing an alarm condition on page 7-5.

Admit or discharge a patient.

View beds outside your care unit.

See Out-of-unit patient beds on page 7-6.

Silence all alarms.

See Silencing alarms on page 5-7.

The multi-patient viewer displays

menu bar

options similar to the following:

«
...
108
109
110
111
112
...
»

Summary of Contents for ApexPro



























































































































































































































Reviews:

No comments

Related manuals for ApexPro

Brand: Parata Pages: 40

Brand: Keiser Pages: 82

Brand: Keiser Pages: 4

Brand: IDEAL Networks Pages: 10

Brand: DAAB Pages: 12

Brand: Trojan Pages: 12

Brand: Tascam Pages: 102

Brand: Dentsply Sirona Pages: 2

Brand: Endura Pages: 10

Brand: Larson Electronics Pages: 5

Brand: Agilent Technologies Pages: 5

Brand: Hyundai Pages: 161

Brand: ZAMST Pages: 3

Brand: DBI SALA Pages: 20

Brand: ulrich medical Pages: 12

Brand: DCD Pages: 4

Brand: Otto Bock Pages: 88

STANDARD LipidoCare

Brand: SD Biosensor Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands