GE ApexPro Operator'S Manual Download Page 189 | Manualshive

Page: 189 / 218

background image

Maintenance

2001989-200E

ApexPro™

C-3

Disposal

WARNING

PACKAGING DISPOSAL—Dispose of all packaging material,
observing all applicable waste control regulations and keeping out of
children’s reach.

WARNING

DISPOSAL—At the end of its service life, the products described in
this manual, as well as its accessories, must be disposed of in
compliance with guidelines regulating the disposal of each product.
If you have any questions concerning disposal of a product, please
contact GE or its representatives.

Cleaning

All equipment should be cleaned on a regular basis. Comply with the policies of your
institution’s infection control unit and/or biomed department. The decision to
disinfect or sterilize must be made per your institution’s requirements with an
awareness of the effect on the integrity of the transmitter and leadwire.

WARNING

Disconnect AC-powered equipment from the power line before
cleaning or disinfecting its surface. Turn off the power to battery-
powered equipment before cleaning or disinfecting its surface.

WARNING

CONTAMINATED LEADWIRES— Contaminated leadwires may
cause infection. Always follow the skin preparation guidelines and
leadwire cleaning instructions provided in this manual.

WARNING

IMPROPER TRANSMITTER/LEADWIRE APPLICATION —
Applying a transmitter and/or leadwire that is not thoroughly dry to
a patient can result in an electrically conductive path being
established and a

Leads Fail

alarm not being provided if leadwires

come off the patient.

CAUTION

Never immerse devices, cables, or leadwires in any liquid.

«
...
187
188
189
190
191
...
»

Summary of Contents for ApexPro



























































































































































































































Reviews:

No comments

Related manuals for ApexPro

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

Brand: BARKO LOADERS Pages: 85

Brand: Danfoss Pages: 106

BOMAG BW 100 ADM-5

Brand: Fayat Pages: 216

Brand: B medical systems Pages: 28

Brand: Gebhardt Anlagentechnik Pages: 152

Brand: Hach Pages: 58

Brand: Hach Pages: 52

Brand: Hanna Instruments Pages: 2

Brand: Hanna Instruments Pages: 2

Brand: Hanna Pages: 12

Brand: Hanil Pages: 24

Brand: Hanil Pages: 32

Brand: Hanil Pages: 24

Brand: Major tech Pages: 12

Brand: Gardco Pages: 17

Brand: H&S Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands