GE akta start Maintenance Manual Download Page 120 | Manualshive

Page: 120 / 214

background image

5.14.1

Firmware update

NOTICE

Before tapping the Firmware update ensure that the system is
connected to a stable source of power such as a UPS. During
firmware update the system should not be switched off.

Prerequisites

•

USB memory stick with at least 10 MB free space.

•

Delete any previous AKTASTRT.src files located on the USB memory stick.

•

Download the latest AKTASTRT.src file from the product support page onto the USB
memory stick, refer to (www.gelifesciences.com/AKTA).

Instructions

Follow the instructions below to update the firmware.

Action

Step

Plug the USB memory stick into the USB port located on ÄKTA start.

1

In the System screen, tap Firmware update.

2

Result: The following screen opens.

120

ÄKTA start Maintenance Manual 29-0603-08 AC

5 Service and settings

5.14 System
5.14.1 Firmware update

«
...
118
119
120
121
122
...
»

Summary of Contents for akta start























































































































































































































Reviews:

No comments

Related manuals for akta start

Brand: zipwake Pages: 2

Brand: zipwake Pages: 2

Brand: Landoll Pages: 6

Brand: ParaBody Pages: 9

Brand: ParaBody Pages: 3

Brand: MacDon Pages: 45

Brand: H&S Pages: 30

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: Abicor Binzel Pages: 92

Brand: CAB Pages: 13

Brand: CAB Pages: 30

Brand: CAB Pages: 17

Brand: CAB Pages: 33

Camping Equipment

Brand: C. Crane Pages: 8

Brand: C-Pro Direct Pages: 4

Brand: C-Pro Direct Pages: 4

Brand: RayLight Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands