background image

8

HELPFUL LAMINATING TIPS

•  Do not attempt to laminate abrasive or metal items 

such as staples or paper clips as they will damage 

the heat shoes and rollers.

•  Do not force items into the nip area of the rollers.  

An item that is not easily drawn into the laminator 

is probably too thick to laminate.

•  Wrinkles may result if an attempt is made to 

reposition an item once the rollers have grasped it.

•  Do not stop the laminator before an item has 

completely exited the rear of the laminator.  Even 

a momentary stop will cause a mark (heat line) to 

appear on the laminated item.

Avoid adhesive deposits on the heat shoes and 

rollers by:

•  Use both top and bottom rolls of film.  Both rolls 

must be used for problem free lamination.

•  Do not allow rolls of film to run completely off the 

core.

Operation

CAUTION:  MAKE SURE HEAT SHIELD AND FEED 

TABLE ARE IN THE PROPER POSITION TO OPERATE 

THE UNIT.

1.  Move the main power switch to the “ON” position 

(FIGURE 2).  With the main power switch in the 

“ON” position, the laminator can be turned on or 

off using the standby button (   ) located on the 

control panel.

2.  Select proper film thickness on the control panel 

by pressing the “MIL” button until the light under 

the film thickness is illuminated (FIGURE 3, iii).

3.  Reference table printed on the Feed Table 

to select proper speed based on document 

thickness, or press “Auto” to allow machine to run 

at Auto Speed.

4.  When the laminator reaches operating 

temperature, the ready light indicator will 

illuminate.

5.  Position the item(s) to be laminated on the feed 

table.

6.  Push the “RUN” button.
7.  Slide the item(s) to be laminated into the nip 

rollers.

8.  When the laminated item(s) exits the rear of the 

laminator, press the “STOP” button.

9.  Use the Rear Slitter located at the back of the 

laminator to separate the laminated item(s) from 

the film web.

CLEARING A FILM JAM (WRAP-UP)
Film jams may occur if the laminator is not positioned to 

allow exiting film to drop freely to the floor.  Accumulation 

of laminate as it exits the laminator may cause film to wrap 

around the roller, causing a jam.
To clear a jam, it is necessary to rotate the rollers in a 

reverse direction.

1.  Immediately stop the laminator by pushing the 

“STOP” button.

2.  Remove the feed table and heat shield.
3.  Cut the top and bottom film webs.
4.  Install the feed table with the loose ends of the 

web on top of the table.

5.  Press the “REV” button to run the machine in 

reverse.  Then grasp the loose ends of the web 

and pull straight out to guide the film out of the 

laminator.

6.  When the film has cleared the heat shoes, press 

the “STOP” button.

7.  Thread the film as indicated in the “FILM 

LOADING AND THREADING” section of this 

manual. 

Summary of Contents for Ultima 35 EZload































Reviews: