manualshive.com logo in svg

Gateway E-842R, User Manual

Share
Download
Gateway E-842R User Manual Download Page 31

Array and logical drive section

www.gateway.com

25

Array and Logical Drive 

Section

Description and Condition

Array Status icon

These icons are found in the Array section and depict the current 
state of the specific component.

■

Green - Status is OK.

■

Yellow - Indicates a drive component in a RAID 1, 10, 5, or 50 
array has failed and the array is no longer fault tolerant, or the 
array is in a rebuild cycle. 

■

Red - Indicates an array is invalid or offline due to an error:
RAID 0 = One drive has failed.
RAID 1/10 = Two drives have failed from the same pair.
RAID 5 = Two drives have failed.
RAID 50 = Two drives have failed within the same sub-array.

Logical Drive Status icon

These icons are found in the Logical Drive section and depict the 
current state of the specific component.

■

Green - Status is OK.

■

Yellow - Indicates the logical drive is part of an array that is 
degraded.

■

Red - Indicates the logical drive is part of an array which is invalid 
or offline,
RAID 0 = One drive has failed.
RAID 1/10 = Two drives have failed from the same pair.
RAID 5 = Two drives have failed.
RAID 50 = Two drives have failed in the same sub-array.

Green (Normal)

Yellow (Warning)

Red (Error)

Green (Normal)

Yellow (Warning)

Red (Error)

Summary of Contents for E-842R





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands