manualshive.com logo in svg

Gateway E-842R, User Manual

Share
Download
Gateway E-842R User Manual Download Page 106

CHAPTER 8: Failover, Performance, and Additional Functions

www.gateway.com

100

How StorView server failover works

If you are using the host-based version of StorView, two or more host servers 
must be directly connected to the RAID Storage Solution enclosure and each 
host must have a copy of StorView installed with a Global Access license. If you 
are using the embedded version of StorView, you must have dual controllers 
installed (duplex topology), each with Embedded StorView installed.

At startup, each StorView server creates a device list of all the attached storage 
systems. Then it sends the list out on the network as a device list packet. The 
other StorView servers on the network respond with their device list packets. 
Since the StorView servers are attached to the same storage solution, they have 
the same or similar devices in their device list packet. The identical devices in 
each device list packet are flagged. After analysis, the StorView server with the 
lowest serial number or address takes control of those devices. The other 
StorView Server indicates on its interface that another StorView server is 
monitoring the storage solution.

During normal operations, the StorView server(s) send 

check-in

 packets every 

10 seconds. If three consecutive check-in packets for a specific StorView Server 
are not received, its devices are flagged and the StorView server attached to that 
storage solution with the lowest serial number or address takes control of those 
devices.

StorView performance optimization

You can adjust some parameters on the host HBA and operating system to 
increase the performance of StorView. They are the HBA Execution Throttle 
setting and the operating system's Scatter/Gather registry setting.

Execution throttle

To improve general I/O performance by allowing more commands on the fibre 
bus or the SCSI bus, we recommend changing your host bus adapter’s execution 
throttle parameter to 256. See your host HBA documentation for more 
information.

Scatter/gather

(Microsoft Windows Only) To increase general I/O performance by allowing 
larger data transfers, we recommend editing the 

MaximumSGList

 parameter 

in the registry. The recommended hexadecimal value is 

ff

. The path is:

HKEY_LOCAL_MACHINE/System/CurrentControlSet/Services
/<name of HBA driver>/Parameters/Device/

See your Microsoft Windows operating system documentation for more 
information on editing the registry and your host HBA adapter documentation.

Summary of Contents for E-842R





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands