manualshive.com logo in svg

Gateway E-842R, User Manual

Share
Download
Gateway E-842R User Manual Download Page 27

The work area

www.gateway.com

21

Fan icon

Animated fan icons are displayed in the rear view of the 
enclosure and change colors and text animation according to the 
state of one or both cooling fans.

■

Normal - Both fans are operating normally.

■

Fan 1 Failed - One fan in the fan module has failed. The fan 
which failed is indicated on the icon.

■

Fan 2 Failed - One fan in the fan module has failed. The fan 
which failed is indicated on the icon.

■

Failure - Both fans in the fan module have failed or the cooling 
fan module has been removed.

Power Supply icon

Power Supply icons are displayed on the Main window rear view 
image of the enclosure and change according to the state of the 
specific power supply.

■

A normal gray icon indicates that the power supply is operating 
normally.

■

A red flashing icon with 

Failure

 displayed indicates that the 

subject power supply has failed.

■

A solid red icon indicates that the power supply is missing.

■

Unknown - This icon indicates the enclosure power supply 
information from the SES processor or SAF-TE processes is 
missing or invalid.

RAID Controller icon

Animated RAID Controller icons are displayed on the Main 
window rear view image of the enclosure and change colors 
according to their state.

■

Normal - RAID Controller is operating normally.

■

Error - A RAID Controller has failed in an Active-Active topology 
or the backup battery has failed.

■

Empty - This icon represents the empty controller slot for future 
expansion. A blank plate is shown.

Audible Alarm icon

■

This icon indicates the alarm is off (muted).

■

This icon indicates the alarm is on (continuous), on 
(intermittent), on (remind), or on.

Enclosure Section

Description and Condition

Normal (gray)

Fan 1 Failed (yellow)

Fan 2 Failed (yellow)

Failure (red)

Normal 

Failure

Missing

Unknown

Normal

Error

Empty

Off

On

Summary of Contents for E-842R





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands