manualshive.com logo in svg

Gateway E-842R, User Manual

Share
Download
Gateway E-842R User Manual Download Page 132

APPENDIX B: Event Logs

www.gateway.com

126

The drive w/SN (SAS: 
w/WWN) (Slot <

nn

>, 

Enclosure <

nn

>) (Slot 

<

number

>) (Drive 

<

number

>) has failed due to 

a time-out.

Error
[0xB0E 
(2830)]

Drive error.

Replace the disk drive.

Disabled Enclosure 
<

xxxxxx

> Slot <

nn

> due to 

excessive errors.

Error
[0xB13 
(2835)]

This indicates that the 
controller has shut 
down the slot due to 
multiple errors from 
the drive.
This may be due to a 
bad drive or MUX 
Transition Board.

Removing the drive in 
the identified slot. This 
re-enables the PHY.

SATA Multiplexer switching 
failure on Enclosure 
<

xxxxxx

> Slot <

nn

>.

Error
[0xB13 
(2835)]

This indicates that the 
controller has tried 
multiple times to 
switch the Multiplexer 
on a SATA drive, and it 
has not been 
successful.
This may be due to a 
bad drive or MUX 
Transition Board.

Replace the disk drive 
or MUX Transition 
Board.

Array <

name

> is in a critical 

state.

Error
[0xB1B 
(2843)]

Drive removal or 
failure.

Replace the disk drive 
and rebuild the array.

The drive w/SN (SAS: 
w/WWN) <

xx xx xx xx xx xx

> 

(Slot <

number

>) returned a 

bad status while 
completing a command. 
SCSI Info: Operation <

type

>, 

Status <

type

>.

Error
[0xB27 
(2855)]

Unknown status 
returned by the disk 
drive.

Contact Customer 
Card and provide them 
with a copy of the 
event log.

The drive w/SN (SAS: 
w/WWN) (Slot <

nn

>, 

Enclosure <

nn

>) timed out 

for the SCSI Operation 
<

type

>.

Error
[0xB28 
(2856)]

Drive hardware error or 
bus error.

Check cabling and 
make sure that the disk 
drives are correctly 
seated.

A rebuild has started on the 
drive w/SN (SAS: w/WWN) 
<

xxxxxx

> (Slot <

nn

> (Drive 

<

number

>).

Information
[0xB30 
(2864)]

A rebuild has started.

No action necessary.

A rebuild has completed on 
(Array <

Name

> Drive 

<

number

>).

Information
[0xB31 
(2865)]

A rebuild has 
completed.

No action necessary.

A rebuild has re-started on 
the drive w/SN (SAS: 
w/WWN) <

xxxxxx

> (Slot 

<

nn

> (Drive <

number

>).

Information
[0xB32 
(2866)]

A rebuild has started.

No action necessary.

Drive & Array Event 

Messages

Type [ID]

Cause

Action

Summary of Contents for E-842R





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands