Gateway E-5400 System Manual Download

Page: 14 / 130

System board

Voltage regulator module (VRM) for second processor

ATX power connector

Supplementary AGP Pro50 power connector

Auxiliary power connector

RIMM slots 1 and 2 (Channel A)

AGP (accelerated graphics processor) slot

SCSI LED connector

Diskette drive connector

Secondary IDE connector

Primary IDE connector

Internal speaker

Front system fan connector

Front panel connector

Front chassis intrusion connector (not used)

Auxiliary LED connector

Configuration jumper (J1F2)

Internal MIDI connector

Telephony connector

CD/DVD audio connector

PCI slots (5)

Battery

System fan (not used)

Rear chassis intrusion connector

Rear system fan

RIMM slots 3 and 4 (Channel B)

Microphone-in connector

05030.book Page 7 Monday, November 22, 1999 8:23 AM

Summary of Contents for E-5400



































































































































Search results

Summary of Contents for E-5400

Reviews:

Related manuals for E-5400

Brands by name

Popular brands

Gateway E-5400, System Manual

Search results

Summary of Contents for E-5400

Reviews:

Related manuals for E-5400

Brands by name

Popular brands