Gateway E-5400 System Manual Download | Manualshive

Page: 123 / 130

background image

116

Safety, Regulatory, and Notices

Notices

Copyright © 1999

Gateway, Inc.

All Rights Reserved
4545 Town Centre Court
San Diego, CA 92121 USA

All Rights Reserved

This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or
transmitted by any means or in any form, without prior consent in writing from Gateway.

The information in this manual has been carefully checked and is believed to be accurate. However, changes
are made periodically. These changes are incorporated in newer publication editions. Gateway may improve
and/or change products described in this publication at any time. Due to continuing system improvements,
Gateway is not responsible for inaccurate information which may appear in this manual. For the latest product
updates, consult the Gateway Web site at www.gateway.com. In no event will Gateway be liable for direct,
indirect, special, exemplary, incidental, or consequential damages resulting from any defect or omission in this
manual, even if advised of the possibility of such damages.

In the interest of continued product development, Gateway reserves the right to make improvements in this
manual and the products it describes at any time, without notices or obligation.

Trademark Acknowledgments

AnyKey, black-and-white spot design, CrystalScan, Destination, EZ Pad, EZ Point, Field Mouse, Solo, TelePath,
Vivitron, stylized “G” design, and “You’ve got a friend in the business” slogan are registered trademarks and
GATEWAY, Gateway Profile, Gateway Solo, Gateway Astro, green stylized GATEWAY, green stylized Gateway
logo, and the black-and-white spotted box logo are trademarks of Gateway, Inc. Intel, Intel Inside logo, and
Pentium are registered trademarks and MMX is a trademark of Intel Corporation. Microsoft, MS, MS-DOS, and
Windows are trademarks or registered trademarks of Microsoft Corporation. All other product names mentioned
herein are used for identification purposes only, and may be the trademarks or registered trademarks of their
respective companies.

05030.book Page 116 Monday, November 22, 1999 8:23 AM

«
...
121
122
123
124
125
...
»

Summary of Contents for E-5400



































































































































Reviews:

No comments

Related manuals for E-5400

Network Adapter EmETX-i602

Brand: Socket Pages: 11

Brand: 7starlake Pages: 48

Matrix MXC-4000 Series

Brand: ADLINK Technology Pages: 80

Brand: Montezuma Pages: 24

Brand: Aaeon Pages: 43

Brand: Altair Pages: 35

Brand: Kontron Embedded Computers Pages: 48

Brand: Dell Pages: 45

Brand: Dell Pages: 57

Brand: Dell Pages: 82

Brand: Dell Pages: 20

Brand: Dell Pages: 14

Inspiron 5591 2n1

Brand: Dell Pages: 20

Brand: Dell Pages: 130

Brand: Dell Pages: 66

Brand: Dell Pages: 120

Brand: Dell Pages: 145

Brand: Dell Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands