Gateway E-5400 System Manual Download | Manualshive

Page: 72 / 130

background image

About the BIOS Configuration Manager

65

5

Using the BIOS
Configuration
Manager

About the BIOS Configuration
Manager

The computer’s BIOS has a built-in configuration manager that lets you
configure several basic system characteristics. The settings are stored in
battery-backed RAM and are retained even when the power is off.

Enter the BIOS Configuration Manager by restarting the computer, then
selecting

Enter Setup

with your mouse when the Gateway Logo screen appears.

Upon entering BIOS Configuration Manager, the screen on the following page
is initially displayed.

Important

This BIOS will not display the usual system messages on
the screen when the system is first started. If you require
this information, you must enter the BIOS Configuration
Manager to obtain it.

05030.book Page 65 Monday, November 22, 1999 8:23 AM

«
...
70
71
72
73
74
...
»

Summary of Contents for E-5400



































































































































Reviews:

No comments

Related manuals for E-5400

iPAQ H3700 Series

Brand: Compaq Pages: 56

Brand: J.Burrows Pages: 24

Brand: Arbor Technology Pages: 115

Brand: Aaeon Pages: 64

Brand: Vivo Pages: 3

Optiplex 9010 All In One

Brand: Dell Pages: 67

SIMATIC IPC847C

Brand: Siemens Pages: 46

SIMATIC PC RI25

Brand: Siemens Pages: 64

SIMATIC Panel PC 677

Brand: Siemens Pages: 94

SIMATIC PG 760 PII

Brand: Siemens Pages: 120

Brand: Siemens Pages: 192

SIMATIC IPC847D

Brand: Siemens Pages: 222

Brand: Yamaha Pages: 65

Brand: Yamaha Pages: 72

Brand: Yamaha Pages: 78

Brand: Yamaha Pages: 120

Brand: Yamaha Pages: 420

VAIO VPCSA21GXSI

Brand: Sony Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands