Gateway E-5400 System Manual Download

Page: 98 / 130

Modem problems

Modem problems

The modem is not recognized by the system

Probable Cause

Solution

The modem has not
been added as new
hardware.

Add the modem as new hardware.

The modem is not
connected to a live
phone jack.

Make sure that the line connected to the
modem is live and plugged into the
appropriate port on the modem (line port).

The phone jack is
shared by another
modem or telephone.

If the modem shares the jack with another
device, make sure that the other device does
not have the port open (for instance, someone
is on the phone, or another modem is in use).

The modem is not
configured with a valid
interrupt or address.

Check the system settings for possible
conflicts. If one exists, correct the problem by
selecting an available interrupt and address.

05030.book Page 91 Monday, November 22, 1999 8:23 AM

Summary of Contents for E-5400



































































































































Search results

Summary of Contents for E-5400

Reviews:

Related manuals for E-5400

Brands by name

Popular brands

Gateway E-5400, System Manual

Search results

Summary of Contents for E-5400

Reviews:

Related manuals for E-5400

Brands by name

Popular brands