Gateway E-5400 System Manual Download

Page: 87 / 130

Managing Your System

Monitoring system health with LANDesk

Intel LANDesk

Client Manager is a desktop management interface (DMI) that

lets you monitor the health of your system components. Through LANDesk,
you can view software and hardware properties. You can also set LANDesk to
notify you when system resources reach certain levels.

To install LANDesk Client Manager:

Double-click the

Setup

icon in the c:\dmi folder on your hard drive. The

InstallShield

wizard starts.

Follow the on-screen instructions.

If you are prompted for a password during the installation process, type

lowtco.

LANDesk Client Manager comes with complete documentation and online
help. Refer to these sources for more information on using the software.

05030.book Page 80 Monday, November 22, 1999 8:23 AM

Summary of Contents for E-5400



































































































































Search results

Summary of Contents for E-5400

Reviews:

Related manuals for E-5400

Brands by name

Popular brands

Gateway E-5400, System Manual

Search results

Summary of Contents for E-5400

Reviews:

Related manuals for E-5400

Brands by name

Popular brands