Gateway E-5400 System Manual Download | Manualshive

Page: 23 / 130

background image

16

Case Access

Also follow these static electricity precautions:

■

Avoid static-causing surfaces such as plastic and styrofoam in your work
area.

■

Remove the parts from their antistatic bag or container only when you
are ready to use them. Do not lay parts on the outside of an antistatic
bag or container because only the inside provides antistatic protection.

■

Always hold cards by their edges and their metal mounting brackets.
Avoid touching components on the cards and the edge connectors that
connect to expansion slots. Never slide cards or other parts over any
surface.

05030.book Page 16 Monday, November 22, 1999 8:23 AM

«
...
21
22
23
24
25
...
»

Summary of Contents for E-5400



































































































































Reviews:

No comments

Related manuals for E-5400

Brand: Acer Pages: 106

Brand: Acer Pages: 83

Brand: Acer Pages: 81

Brand: Acer Pages: 89

T230H - Bmidh Wide Touch Screen Display

Brand: Acer Pages: 12

Brand: Acer Pages: 100

Brand: T-MAG Pages: 22

POWERMATE ES 5250 - S

Brand: NEC Pages: 18

POWERMATE VT 300 RELEASE NOTES

Brand: NEC Pages: 16

POWERMATE CT 815 - RELEASE NOTES

Brand: NEC Pages: 155

Brand: NEC Pages: 6

POWERMATE ES Series

Brand: NEC Pages: 132

POWERMATE ES Series

Brand: NEC Pages: 8

Brand: NEC Pages: 167

Brand: NEC Pages: 1

Brand: Seneca Pages: 8

Brand: IBM Pages: 27

Brand: DFI Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands