background image

 

 

__p

DS67U Quick Guide【 English 】

53R-DS67U3-H001

C. Component Installation

D. Complete

3.  Lay the HDD or SSD into its drive bay and push it gently to the right  

  until it clicks into place.

1. Replace the covers and refasten the screws.

3.  Complete.

A. Begin Installation

1. Unscrew two screws of the chassis cover.

For safety reasons, please ensure that the power cord is discon- 

nected before opening the case.

1

2

2. Slide the cover forwards and upwards.

4.  Refasten screws.

Left / Right Panel

Back Panel

Front Panel

F1. USB 3.0 Ports x2
F2. USB 2.0 Ports x2
F3. Power LED
F4. HDD LED
F5. Power Button
F6. COM 1 :  

 

Support RS232/RS422/RS485 

F7. COM 2 :  

 

Support RS232

F8. SD Card Reader

B. Memory Module Installation

notch

Supports DDR3L SO-DIMM 

(1.35V)

1. Locate the SO-DIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.

3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the locking  

  mechanism.

5. Repeat above steps to install additional memory modules, if required.

2. Place the HDD or SSD in the rack and secure with the two screws from  

  the side.

1. Unscrew the rack from chassis.

Motherboard Illustration Back

Jumper Settings

 

Safety Information

 

Read the following precautions before setting up a Shuttle XPC.

CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same or equivalent as recommended by Shuttle. 

Dispose of used batteries according to the manufacturer's instructions.

 

Kensington

®

 Lock

 

Kensington

®

 Lock

45-degree 

angle

1

2

3

Latch

Latch

SD Card Reader FFC 

Connector - CON3

Intel

®

 

Celeron

®

 / Core

 i series 

processor

Motherboard Illustration Front

This mainboard does only support 1.35V DDR3L memory 

modules.

B1.  

External Power & Clear CMOS 

       (Pin definition     )
B2.  DisplayPort
B3.  HDMI Port
B4.  MIC-in Jack
B5.  Headphone Jack
B6.  USB 2.0 Ports x2
B7.  LAN Ports x2 
B8.  DC IN
B9.  Connectors for WLAN antennas

J4

USB 2.0 Ports x2

J1

J2

COM Port 1

LAN Ports x2 

USB 2.0 Ports x2

Headphone JACK

MIC-in JACK

HDMI Port

DisplayPort

COM1 & COM2 

Power Switch - JP1

Power Button - SW3

M.2  2242 M Key Slots

External Power SW & 

Clear CMOS - SW2

 

RTC Battery Connector - BAT1

HDD LED

Power LED

DC IN

COM Port 2

J3

2.5 inch HDD Slot

DDR3L SO-DIMM Slots

AC Back Auto Power ON 

(DEFAULT =>Disable,  

short 1-2) - JP9

J4

L

The product’s colour and specifications may vary from the actually shipping product.

F3

F4

F5

F6

F8

F7

F1

F2

M.2 2230 E Key Slots

USB 3.0 Ports x2

2. 

Screw the included antennas onto the appropriate connectors at the back panel (B9). 

  Make sure they are aligned vertically or horizontally to achieve the best possible  

  signal reception.

5.  As shown, unfasten the screw first.
6.  Install the M.2 device into the M.2 slot and secure with the screw.

Debug Header

Please press the "Del" key while booting to enter BIOS.  

Here, please load the optimised BIOS settings.

 

Operation Position:

Please make sure to use either the supplied feet or the VESA mount.

Make sure all antennas are aligned in the correct direction.

J1

COM Port 1

RS-232, RS-422, RS-485 switch by BIOS setting

1  2  3  4  5 

6  7  8  9 

COM1 (RS232)

Pin Signal Name

Pin Signal Name

1

DCD

2 RX

3

TX

4 DTR

5

GND

6 DSR

7

RTS

8 CTS

9

RI-

COM1 (RS422)

Pin Signal Name Pin Signal Name

1

TXD-

2

TXD+

3

RXD- 

4

RXD+

5

GND

6

---

7

---

8

---

9

---

COM1 (RS485)

Pin Signal Name

Pin Signal Name

1

Data-

2 Data+

3

---

4 ---

5

GND

6 ---

7

---

8 ---

9

---

COM1 & COM2 Power Switch

5  7  9

6  8  10

J2

JP1

COM1 (pin9)

COM2 (pin9)

Short Pin

Function

Short Pin

Function

1-2 (Default) RI1

3-4 (Default)

RI2

5-7

+5V

6-8

+5V

7-9

+12V

8-10

+12V

AC Back Auto Power ON

1  

2  

J3

JP9

Pin

AC Back auto Power ON function

Short 1-2

Disable (Default)

Open

Enable

J4

External Power SW & Clear CMOS

1

3

2

4

SW2

Pin Signal Name
1

PWRSW-

2

+5V

3

GND

4

RTC_RST#

62R-DS67U0-5201    DS67U
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide

B1

B3

B4

B5

B7

B8

B2

B6

B9

Reviews: